구리는 인간의 삶에서 중요한 역할을합니다. 전기 공급에서 물 공급에 이르기까지 구리는 모든 것을 가능하게했습니다.

It allows the electric current to passes through it with the same voltages; it is the good conductor of electricity.

The copper is used in the electric appliances, almost every high-quality motors have the copper wires in them.

In the past, the cutlery item is made from the copper with are a good conductor of the heat and cold. Copper itself is soft in nature but when you mix it with any other metal it becomes hard.

What is the hardness of metals?

Hardness is termed as the resistance of the metals to indentation. Hardness doesn’t remain forever it depends on the strength and the plasticity of the metal.

The hardness of the metal depends on the method of measurement. The measurement results are expressed in the quantitative figures.

The resistance in the metal can make them hard, resistance refer to the four different things. They are scratching, abrasion, cutting, and penetration.

The different properties of the metal give them the ability to resist or deformed permanently when the load is applied.  The greater resistance to deformation shows the greater hardness of the materials.

The hardness of the material is commonly used for the quality testing and quality control of the materials.

The main reason for the quality control of the materials is because they are fast and known to be the nondestructive tests. There are some of the important measurements for the hardness of the materials described below:

Indentation hardness: it is the simple method in which we can measure the resistance of the material to deformation when the constant pressure or load from the sharp object is applied to it. It can be measured through the Rockwell, Brinell, shores, and Vickers.

Scratch hardness: in this method, we measure the resistant of the metal for permanent plastic deformation or fracture due to the friction of the sharp object on it. For the measurement of this method, the Mohs scale is used.

Rebound harness: rebound hardness is the method in which the diamond-tipped hammer is dropped from a certain height on the specific material to check its hardness. The Bennett hardness and the Leeb rebound hardness scale are used to measuring the rebound hardness.

The conversion table is used to convert the one scale to another; it is used for the practices. There is an individual measurement scale for each of these classes.

Properties of copper: (related to hardness)

The copper is used for the sheeting and in the form of strips commonly. It is consists of 99.9 percent pure copper and the 0.1 percent may be the other metal.

The pure form of the copper is soft which is extremely malleable and can be used for the different applications like intricate ornamental works.

In the past, it is commonly used in the construction of buildings. The heavy gauge materials are used along with the copper because copper has a low strength than other metals.

With the passage of time, the copper is replaced with other strong metals in the building constructions.

Many years ago the cold-rolled copper is introduced and the gauge of the other materials is reduced.

The cold-rolled copper has a long life with low maintenance than other materials.

Cold rolled copper is hard and is less malleable than the soft tamper copper. It is the popular form of copper which is used in construction purposes.

The common mechanical properties of the copper are strength, hardness, and ductility which determine its condition.

Copper is can be converted into the hard from soft; the method used to range the copper is cold working. Annealed (soft) copper is 40HV of hardness with the tensile strength of 200 N/mm2 and after the cold work, it has the hardness of 110 HV with the tensile strength of 360 N/mm2. The ductility of the annealed copper is greater than the cold-worked copper.

You can increase the strength and the hardness of the copper easily. The common way of increasing the strength of the copper is through the alloying, but it can affect the conductivity of the electricity.

The hardening process is done by heat treatment and can result in the tensile strength of 1500 N/mm2.

Test for hardness:

There are different types of the test to determine the hardness of the metals, but in the case of the copper, there are only three different types of tests used to determine its hardness. The types of tests are discussed below:

Rockwell Test:

The Rockwell Hardness test is a popular test to check the hardness of the copper.  It consists of thirty different tests with the number of loads and indenter configurations.

Scale B and C are only used for the thickness of the 1mm and can be used for the copper alloys with this thickness. For the thin products the testing should be done through the superficial scales N and T. the hardness of the thin materials are checked with the microhardness scales.

Brinell Test:

It is a large and extensive indentation test, which is not suitable for the thin and wire type materials. It is popular for testing the large rods, bars, plates, and other heavy materials.

The testing of these materials will produce large indentations. The Brinell test is run only for the materials who are thicker than the minimum of 3.2 inches.

Vickers and Knoop Tests:

The Vickers test is also known as the diamond pyramid hardness test. The load uses in this test is between 1 to 120 kg. If the weight of the material is less than 1 kg than the Vickers microhardness test will perform.  And the knop test is specially designed for the micro indentation hardness testing.

The testing is performing with the help of the elongated indenter.

All above the tests are designed to check the hardness of the copper, the test selection is depended on the quality and the type of the copper.

경도 시험기를 구입 하시겠습니까?전문가에게 문의하십시오!

우리는 Rockwell, Victor, Brinell 및 휴대용 경도 시험기를 제조합니다!

ko_KR한국어
en_USEnglish fr_FRFrançais de_DEDeutsch es_ESEspañol ja日本語 ru_RUРусский ko_KR한국어
우리와 채팅
우리와 채팅
메시지를 남겨 주시면 12 시간 이내에 답변을 드리겠습니다!
연결...
메시지를 남겨 주시면 12 시간 이내에 답변을 드리겠습니다!
메시지를 남겨 주시면 12 시간 이내에 답변을 드리겠습니다!
:
:
:
메시지를 남겨 주시면 12 시간 이내에 답변을 드리겠습니다!
:
:
이 채팅 세션이 종료되었습니다.
이 대화가 유용 했습니까? 이 채팅 세션에 투표하세요.
좋은 나쁜