[Upgrade Version] 5 Inch CCTV Camera Tester, Electop 4 in 1 AHD TVI CVI Coaxial HD Video Monitor Tester ,Support Analog Video Test ,UTP Cable Test ,VGA/HDMI Input ,DC12V Output Camera Tester$139.87
[Upgrade Version] Electop Wrist CCTV Tester, 5 Inch 4 in 1 HD 1080P Portable Camera Tester AHD TVI CVI CVBS Tester VGA TFT LCD Monitor Analog Video Test Cable Test PTZ Control 12V Power Output$89.99
0-90% Brix Meter Refractometer,V-Resourcing Portable Hand Held Sugar Content Measurement for Sugar, Food, Fruit, Beverages Honey$24.99
19 in 1 Network Cable Tester Rj45 Kit Rj11 Cat5 Cat6 6P6C 8P8C Connectors Portable Phone Cable Crimper, Stripper Cutter Pliers Network Tool Set Professional$17.99
2 in 1 Water Quality Chlorine and PH Tester Meter, Portable Digital Water Quality Tester Analysis Monitor,PH and Chlorine Level CL2 Chlorine Tester for Swimming Pool$35.89
2021[Upgraded]Best Sellers High Accuracy Professional Jeweler Diamond Tester II V2 for Novice and Expert -Diamond Selector II (Diamond Tester)$16.66
220V ~ 250V Portable Electrical Smart Socket Tester & 50-60Hz AC 12-1000V Pen Circuit Detector$34.98
4 Inch Portable CCTV Tester Up to 4K 8MP H265 Camera-Support IP,CVBS Analog Camera,AHD,TVI,CVI-Built in WiFi, PoE Power Output,PTZ Control, Onvif$219.99
(as of [price_update_date] – Details)
Serial Wombat I/O expansion chips make your favorite single board computer better.
A Serial Wombat chip isn’t a device you program – It’s a helpful accessory that you command to expand your capability. Like other IC’s, it’s easily added to an I2C or Serial Bus. Unlike other IC’s, it has built in firmware that lets you offload simple but timing sensitive tasks from your code or sketch to the Serial Wombat chip’s firmware and CPU.
Unlike single-purpose expansion chips such as the MCP3008 or PCF8574, Serial Wombat chips provide both digital and analog capability, plus an additional onboard processor core and preprogrammed firmware to manage I/O tasks so the main board doesn’t have to.
【𝐄𝐚𝐬𝐭𝐞𝐫 𝐏𝐫𝐨𝐦𝐨𝐭𝐢𝐨𝐧】 Hardness Tester, Shore Type A/O/D Rubber Tire Durometer Hardness Tester Meter 0-100 HA(A Type)$20.93
0-100HD Shore A Hardness Tester Meter,Digital Portable Durometer Scale for Rubber, Silica Gel, tire and Plastic$32.99
0~100HA Rubber Tire Shore A Durometer Hardness Digital Meter Tester Large LCD Display for General Rubber, Synthetic Rubber, Soft Rubber, Poly Fat, Leather and Wax$28.90
100HD A Digital Durometer Shore Rubber Hardness Tester with LCD Display Meter$32.99
12V Electronic Automotive Relay Tester Auto Car Diagnostic Battery Checker Tool Relay Tester Automotive Kit
15A Male to 30A Female RV Power Adapter Cords Electrical Twist Lock Adaptors 12-inch(15M30T)$19.99
16 in 1 Drinking Water Test Kit |High Sensitivity Test Strips detect pH, Hardness, Chlorine, Lead, Iron, Copper, Nitrate, Nitrite | Home Water Purity Test Strips for Aquarium, Pool, Well & Tap Water$20.98
AIRIC Voltage Tester Non Contact AC Pen Electrical Tester Adjustable Sensitivity, Outlet Circuit Tester, LED Flashlight, Beeper Alarm, 12V-1000V/48V-1000V & Null Live Wires Voltage Detector$12.99
The Serial Wombat 4B smart I/O expansion chips are compatible with Arduino, Compatible with Raspberry Pi, native embedded systems or any other system that can communicate by I2C. Downloadable code libraries are compatible with Arduino. Protocol documentation is available for users on other platforms to write their own interface using a simple I2C protocol at up to 400kbps.
Serial Wombat chips are supported by IDE libraries that can be downloaded through the official library manager.
Serial Wombat chips clean up your project’s wiring
Since Serial Wombat chips require only 4 wires from the main board (power, ground, and communications) it can clean up your project’s wiring by putting the I/O pin you need right next to the device being interfaced. In this example 3 pots and a button require only 4 wires to the main board instead of 6 (4 signals plus power and ground).
(Sample application – Single board computer, pots, buttons, breadboard and and wire not included)
Serial Wombat Chips make I/O intensive projects easier
I/O where you need it, with smarts to match
Serial Wombat chips simplify tasks commonly performed with a single board computer. Driving multiple servos, reading multiple rotary encoders, debouncing buttons, and reading A/D inputs at the same time can be challenging, particularly if integration of multiple 3rd party libraries is necessary.
Serial Wombat chips automate these tasks using the chip’s on-board processing core so your sketch only has to query or command the Serial Wombat chip as needed instead of managing the I/O in real time.
Servo Pin Mode
Each Serial Wombat 4B chip can control up to three servos simultaneously. The library interface is compatible with Arduino standard Servo.h interfaces, but adds additional features such as direction reversal and a 16 bit position option that provides higher resolution than the 180 degree interface in the standard library.
(Picture shown is a sample application. Wires, breadboard and servos not included.)
Rotary Encoder Pin Mode
Each Serial Wombat 4B chip can monitor up to two Rotary Encoders simultaneously. The Serial Wombat chip keeps a net directional count of transitions so your sketch doesn’t have to catch every pin change. Instead, your sketch simply asks the Serial Wombat chip for the net change since the last time you asked. Your sketch can do this as often or slowly as you like. On-board pull-ups, counting on both or single edges, and the ability to add debouncing to transitions add versatility.
(Picture shown is a sample application. Wires, breadboard and rotary encoders not included.)
A/D Converter Pin Mode
Each Serial Wombat 4B chip can interface to up to three analog signals simultaneously.
(Picture shown is a sample application. Wires, breadboard and potentiometers not included.)
The 10-bit 1kHz sampled data can be accessed as a single sample, 64-sample averaged values or first order digital filtered value to minimize latency, increase resolution or smooth erratic signals.
The Serial Wombat 4B chip’s supply range of 2.5V to 5.5V and I2C interface allow it to directly measure 5V inputs and while interfacing to a 3.3V main board.
Debounced Input Pin Mode
Each Serial Wombat 4B chip can debounce up to 4 input pins. Each debounce pin can be configured for optional internal pullup, debounce time, and inversion. The debounce pin mode also monitors the count of pin transitions between reads from the host, and the period of time the input (such as a button) has been active to ease creation of sophisticated user interfaces.
(Picture shown is a sample application. Wires, breadboard, buttons and single board computer not included.)
PWM Pin Mode
Each Serial Wombat 4B chip can drive up to 3 PWM outputs at selected frequencies between 1Hz and 31kHz with 10-bit resolution. All PWMs within a single Serial Wombat 4B chip run at the same frequency.
WatchDog Pin Mode
Watchdog digital outputs allow the host to instruct the Serial Wombat chip to change an output pin if a timer is not reset within a specified timeframe. This can be used to reset the host in the event that it locks up, or to shut off outputs which should not be left on in the event of communications interruption or software lockup. The Serial Wombat chip itself can also optionally be reset on timeout.
This feature makes a Serial Wombat chip a great add-on for single board computers which are remotely located.
(Picture shown is a sample application. Wires, breadboard, and Single Board Computer not included.)
Protected Output Pin Mode
The Serial Wombat can quickly change the state of an output pin based on analog or digital input from another pin. This allows the Serial Wombat chip to quickly shut off an output if a fault is detected, potentially avoiding damage to your circuit in the event of a short. This feature is not intended for use in safety-critical applications.
Pulse Measurement Pin Mode
Each Serial Wombat 4B chip can measure up to 4 pulse inputs with a resolution as fine as 8 microseconds. A Serial Wombat chip can therefore easily turn an RC receiver into an I2C accessible device.
(Picture shown is a sample application. Wires, breadboard, Single Board Computer, RC Transmitter and receiver not included.)
I2C <–> UART Bridge
Each Serial Wombat 4B chip can add an additional UART TX, UART RX or both to your system via I2C. Standard Baud rates are supported.
This is an ideal way to add an additional debug output if your system is already using its UART for other purposes.
Users should note that constant, full-speed communications at high baud rates may lead to data loss due to the overhead of encapsulating the UART data in the Serial Wombat communication protocol which is optimized for low-latency I/O operations rather than bulk transfers.
Digital Input and Output
Each Serial Wombat 4B chip has 3 Input/Output/Analog capable pins and one input-only pin (pin 0).
Each pin has an optionally-enabled internal pull-up.
Output pins can be push-pull or optionally open-drain. Each pin can sink or source up to 25mA of current . (Compare to 12mA on ESP8266/Node MCU or 7mA for Seeduino Xiao).
The Serial Wombat 4B chip’s 2.5V to 5.5V source voltage range and I2C interface provides a path for 5V to 3.3V interfacing.
Supply Voltage Measurement
Serial Wombat chips can measure and report their own supply voltage. This allows monitoring of the supply voltage and conversion of A/D counts into voltage measurements.
(Picture shown is a sample application. Wires, breadboard, batteries and battery holder not included.)
The Serial Wombat 4B chip has a built in bootloader which allows new versions of firmware to be loaded using a UART interface on pins WP0 and WP1. This allows upgrades, side-grades to other Serial Wombat firmware that use the same microcontroller, changing of I2C addresses, or uploading of user-customized firmware.
Extensive Videos, Documentation and Source Code make easy things easy and hard things possible
Online Tutorial Videos
Numerous support videos are available online, from simple getting-started videos to in-depth tutorials on use of individual pin modes. Each video uses one or more of the examples that come with the Compatible with Arduino library which is available through the IDE’s library manager.
Extensive Doxygen based Documentation
The Serial Wombat project’s source code and host side library are heavily documented within the source. The open source Doxygen tool is used to generate documentation for the project as a whole, and for all of the interfaces for each pin mode. This documentation is available through the project’s GitHub pages area.
Source Code is Open Source
Have a nuanced question that the documentation doesn’t answer? Or need to adapt the firmware to do something different? The Serial Wombat firmware’s source code is open source under an MIT license and available on GitHub.
Easily add a few more I/O or A/D channels to your project through I2C
Do complex tasks with a few simple calls to the API available for download through the IDE Library Manager
Many support videos and extensive documentation available online.
3 Input/Output and 1 Input Only pin on each chip. Each pin can be assigned a specific function such as Servo, Quadrature Encoder, A/D conversion, UART Bridge
Use all 4 chips together, or in 4 different projects. 100nF capacitors included. Uncut decal strip with 8 decals included. Upgradable Open Source Firmware available on GitHub.
[Upgraded] High Accuracy Diamond Tester Professional Jeweler for Novice and Expert – Diamond Selector II 9V Battery Included(Black Diamond Testers)$16.99
#moh – 11oz Hashtag Ceramic Colored Handle and Inside Coffee Mug Cup, Black$22.99
#moh – 12oz Hashtag Camping Mug Stainless Steel, Black$22.89
#moh – 14oz Hashtag White Ceramic Statesman Coffee Mug$24.89
#moh – 14oz Stainless Steel Travel Mug, Silver$26.99
#moh – 20oz Hashtag Stainless Steel White Water Bottle with Carabiner, White$24.89
#moh – Ceramic 11oz White Mug, White$22.89
#tester – 11oz Ceramic Colored Handle and Inside Coffee Mug Cup, Black$22.99